{"title":"Temperature - Spring Contact (TS)","description":"","products":[{"product_id":"tsma-temperatursensor-mit-gefederter-messspitze","title":"TSMA temperature sensor with spring-loaded tip","description":"\u003cp\u003eThe \u003cstrong\u003eTSMA\u003c\/strong\u003e is a temperature sensor with a spring-loaded measuring tip, manufacturer type Müller \u003cstrong\u003eMKTS-SP\u003c\/strong\u003e.\u003c\/p\u003e\n\u003cp\u003eIt is built for bearing and surface temperatures: the spring presses the tip against the measuring point with \u003cstrong\u003e14 mm of travel\u003c\/strong\u003e and keeps contact even when the component moves or expands with heat – a rigidly screwed-in sensor loses contact at such a point. The process connection is 3\/8\", 1\/2\" or 3\/4\", the insertion length 45 or 65 mm as well as custom, the sensor tube Ø 6 mm made of \u003cstrong\u003e1.4571\u003c\/strong\u003e stainless steel, plus knurled screw 1.4541, compression spring in 1.4310 spring steel, PTFE insulating body, weight approx. 200 g. Protection is \u003cstrong\u003eIP 65 at the electronics and IP 68 at the sensor\u003c\/strong\u003e, encapsulated inside.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eThis sensor does not withstand process pressure.\u003c\/strong\u003e The process connection has no sealing effect. It measures at the surface and in the bearing, not inside a closed medium; the pressure equipment directive therefore does not apply. Two versions are available: resistance directly on the connector, or \u003cstrong\u003e4 … 20 mA with HART\u003c\/strong\u003e in the 2-wire loop, set in software over HART.\u003c\/p\u003e\n\u003cp\u003eThe input takes \u003cstrong\u003eone or two Pt100\u003c\/strong\u003e or \u003cstrong\u003ePt1000\u003c\/strong\u003e in 2-, 3- or 4-wire connection in classes A, B and AA, alternatively a \u003cstrong\u003etype K thermocouple with a cross-band\u003c\/strong\u003e. The range runs from \u003cstrong\u003e-50 … +150 °C\u003c\/strong\u003e at a smallest span of 50 K. Total accuracy is \u003cstrong\u003e0.3 % of the range\u003c\/strong\u003e at \u003cstrong\u003e16 bit\u003c\/strong\u003e, the response time 20 ms, the measuring rate 10 measurements per second, the transfer characteristic linear with temperature. The sensor is supplied from the HART current loop with \u003cstrong\u003e12 … 40 VDC\u003c\/strong\u003e, with reverse polarity protection.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNote before ordering:\u003c\/strong\u003e The ambient temperature is not the medium temperature – without a transmitter the ambient may be -20 … +100 °C, with a transmitter only -20 … +80 °C; which neck length or insulation a hot medium requires, the source does not say. The MK product code is used three times by the manufacturer – MKTS, MKTS-GL and MKTS-SP, with a different meaning of the following digits in each case; when ordering, the type designation belongs in plain text, not just the code. Ten electrical connections are available; two sensors do not work with every connector. Configuration uses the \u003cstrong\u003eHART interface with USB and software\u003c\/strong\u003e, order number 01310-00220. No CE marking is documented in the manufacturer's data sheet, and no declaration of conformity is available for this version. The version with IO-Link is the \u003cstrong\u003eTSMB\u003c\/strong\u003e (MKTS-SPIO).\u003c\/p\u003e\n\u003ch3\u003eBenefits at a glance\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eSpring-loaded measuring tip, 14 mm ±1 mm of travel\u003c\/li\u003e\n\u003cli\u003eKeeps contact on moving and expanding components\u003c\/li\u003e\n\u003cli\u003ePt100, Pt1000 or type K thermocouple\u003c\/li\u003e\n\u003cli\u003eRange -50 to +150 °C, smallest span 50 K\u003c\/li\u003e\n\u003cli\u003eResistance direct or 4 … 20 mA with HART, 0.3 % of the range\u003c\/li\u003e\n\u003cli\u003eInsertion length 45 or 65 mm, sensor tube 1.4571\u003c\/li\u003e\n\u003cli\u003eIP 65 at the electronics, IP 68 at the sensor\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"octogon Shop","offers":[{"title":"Default Title","offer_id":57245618831686,"sku":null,"price":0.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/5558\/6374\/files\/TSMA_MKTS-SP_titelbild_2a57f779-2669-4376-8a67-3184cf076f1f.webp?v=1788951932"},{"product_id":"tsmb-anlegesensor-gefedert-io-link","title":"TSMB spring-loaded surface sensor with IO-Link","description":"\u003cp\u003eThe \u003cstrong\u003eTSMB\u003c\/strong\u003e is a contact sensor with a spring-loaded measuring tip and an IO-Link interface, manufacturer type Müller \u003cstrong\u003eMKTS-SPIO\u003c\/strong\u003e.\u003c\/p\u003e\u003cp\u003eIt measures on the surface and in bearings: The compression spring holds the measuring tip with a \u003cstrong\u003e14 mm travel (±1 mm)\u003c\/strong\u003e at the measuring point, even if the component moves or expands due to heat – a rigidly screwed-in sensor would lose contact in such a situation. The sensor tube measures \u003cstrong\u003eØ 6 mm\u003c\/strong\u003e made of stainless steel \u003cstrong\u003e1.4571\u003c\/strong\u003e, the compression spring is made of spring steel \u003cstrong\u003e1.4310\u003c\/strong\u003e, the protection class is \u003cstrong\u003eIP 65 \/ IP 68\u003c\/strong\u003e, the installation length is \u003cstrong\u003e45 or 65 mm\u003c\/strong\u003e, the weight is approximately \u003cstrong\u003e200 g\u003c\/strong\u003e.\u003c\/p\u003e\u003cp\u003eThe mechanics are the same as with the \u003cstrong\u003eTSMA\u003c\/strong\u003e (MKTS-SP); instead of a HART transmitter, an IO-Link transmitter is installed here. The measured value is sent digitally to the \u003cstrong\u003eIO-Link\u003c\/strong\u003e master, and the sensor is also parameterized there – a configuration device is not necessary, the description of the values is in the device file \u003cstrong\u003eIODD MKTS-SPIO\u003c\/strong\u003e. The electrical connection is \u003cstrong\u003eM12x1 four-pin\u003c\/strong\u003e as the only option; the sensor does not have a display or limit contacts.\u003c\/p\u003e\u003cp\u003eThe input has \u003cstrong\u003ea Pt100\u003c\/strong\u003e in a \u003cstrong\u003e3-wire circuit\u003c\/strong\u003e or a thermocouple \u003cstrong\u003eType J, K or N\u003c\/strong\u003e. The nominal range extends from \u003cstrong\u003e-50 … +150 °C\u003c\/strong\u003e in all versions; a measuring range of \u003cstrong\u003e0 … 100 °C\u003c\/strong\u003e is set ex works, customizable. The source states the accuracy as \u003cstrong\u003emax. 0.02 % of the range\u003c\/strong\u003e plus sensor error at \u003cstrong\u003e16 Bit\u003c\/strong\u003e and \u003cstrong\u003e20 ms\u003c\/strong\u003e response time, powered by \u003cstrong\u003e24 VDC\u003c\/strong\u003e with reverse polarity protection.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNote before ordering:\u003c\/strong\u003e This sensor does not withstand process pressure. The source explicitly states: System pressure not possible, the process connection has no sealing effect; the Pressure Equipment Directive is therefore not applicable. The ambient temperature is not the medium temperature: The electronics in the head tolerate \u003cstrong\u003e-20 … +80 °C\u003c\/strong\u003e, the medium up to +150 °C; the source does not state what neck length or insulation is required for this. The accuracy specification is remarkably favorable: 0.02 % of the range at 16 Bit, while the sister sheets with 24 Bit only guarantee 0.1 % and the MKTS-SP with the same design states 0.3 % – before designing, the value must be confirmed with the manufacturer, the sensor error is always added. The relationship between filter and response time is also striking: 25 s filter at 20 ms response time. The datasheet does not specify a minimum span. A CE mark is not documented, a declaration of conformity is not available; explosion protection is also not documented.\u003c\/p\u003e\u003ch3\u003eAdvantages at a glance\u003c\/h3\u003e\u003cul\u003e\n\n\u003cli\u003eSpring-loaded measuring tip, travel 14 mm ±1 mm\u003c\/li\u003e\n\n\u003cli\u003eIO-Link with signal level 0\/24 V, parameterization via the master\u003c\/li\u003e\n\n\u003cli\u003eRange -50 to +150 °C, factory setting 0 … 100 °C\u003c\/li\u003e\n\n\u003cli\u003eInstallation length 45 or 65 mm, sensor tube Ø 6 mm made of 1.4571\u003c\/li\u003e\n\n\u003cli\u003eVersion with HART available as TSMA\u003c\/li\u003e\n\n\n\u003c\/ul\u003e","brand":"octogon GmbH","offers":[{"title":"Default Title","offer_id":57356932645190,"sku":null,"price":0.0,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0819\/5558\/6374\/files\/TSMB_produkt_1b00777b-4c87-4666-b6a6-cf34fa5127d4.webp?v=1789243718"}],"url":"https:\/\/octogon.org\/en\/collections\/temperature-spring-contact-ts.oembed","provider":"octogon GmbH","version":"1.0","type":"link"}